The concept of piezoelectric energy production is based on energy-harvesting devices using generation materials such as single crystals, ceramics, polymers, and composites. These production systems can harvest wasted environmental energy and convert it essentially into electrical energy. There are different nano- and microscale power harvesters which are increasingly useful for powering mobile electronics and low-power devices, even in hardly accessible areas. Despite many efforts in the development of new materials, the most widely used materials in device applications remain the ceramics of the lead zirconate titanate family, since they still present the higher output performances in the range of milliwatts of generated power.

Increasing the scientific knowledge of the population through education is a developmentstrategy towards a sustainable future. However, there is no equity in the access to science educationand scientific knowledge. The aim of this paper is to present and analyse a science kit named “Energy,Environment and Sustainability” (KEAS). Based on research conducted in Guinea-Bissau, it exploresstrategies to promote science education for a sustainable future. The strengths and limitations ofthe KEAS were studied using different data collection methods, including interviews, observation,survey, focus groups and document analysis. The participants were teacher trainers from the Guinea-Bissau School of Education. It is concluded that the KEAS is a feasible and suitable teaching strategyappropriate to the context, having the potential to contribute to learning about the environment andsustainability. Further, it addresses real problems for which students should acquire knowledge andskills in order to be able to make informed choices.

Efficient energy storage systems are increasingly needed due to advances in portable electronics and transport vehicles, with lithium-ion batteries standing out among the most suitable energy storage systems for a large variety of applications. In lithium-ion batteries, the porous separator membrane plays a relevant role as it is placed between the electrodes, serves as a charge transfer medium, and affects the cycle behavior. Typically, porous separator membranes are comprised of a synthetic polymeric matrix embedded in the electrolyte solution. The present chapter focus on recent advances in synthetic polymers for porous separation membranes as well as on the techniques for membrane preparation and physicochemical characterization. The main challenges to improve the synthetic polymer performance for battery separator membrane applications are also discussed.

Industry 4.0 is accelerating the growth of connected devices, resulting in an exponential increase in generated data. The current semiconductor technology is facing challenges in miniaturization and power consumption, demanding for more efficient computation where new materials and devices need to be implemented. One of the most promising candidates for the next technological leap is the memristor. Due to their up-scale manufacturing, the majority of memristors employed conventional deposition techniques (physical and chemical vapor deposition), which can be highly costly. Recently, printed memristors have gained a lot of attention because of their potential for large-scale, fast, and affordable manufacturing. They can also help to reduce material waste, which supports the transition to a more sustainable and environmentally friendly economy. This review provides a perspective on the potential of printed electronics in the fabrication of memristive devices, presenting an overview of the main printing techniques, most suitable for memristors development. Additionally, it focuses on the materials used for the switching layer by comparing its performance. Ultimately, the application of printed memristors is highlighted by showing the tremendous evolution in this field, as well as the main challenges and opportunities that printed memristors are expected to face in the following years.

Dielectric Barrier Discharge (DBD) plasma actuators are simple devices with great potential for active flow control applications. Further, it has been recently proven their ability for applications in the area of heat transfer, such as film cooling of turbine blades or ice removal. The dielectric material used in the fabrication of these devices is essential in determining the device performance. However, the variety of dielectric materials studied in the literature is very limited and the majority of the authors only use Kapton, Teflon, Macor ceramic or poly(methyl methacrylate) (PMMA). Furthermore, several authors reported difficulties in the durability of the dielectric layer when the actuators operate at high voltage and frequency. Also, it has been reported that, after long operation time, the dielectric layer suffers degradation due to its exposure to plasma discharge, degradation that may lead to the failure of the device. Considering the need of durable and robust actuators, as well as the need of higher flow control efficiencies, it is highly important to develop new dielectric materials which may be used for plasma actuator fabrication. In this context, the present study reports on the experimental testing of dielectric materials which can be used for DBD plasma actuators fabrication. Plasma actuators fabricated of poly(vinylidene fluoride) (PVDF) and polystyrene (PS) have been fabricated and evaluated. Although these dielectric materials are not commonly used as dielectric layer of plasma actuators, their interesting electrical and dielectric properties and the possibility of being used as sensors, indicate their suitability as potential alternatives to the standard used materials. The plasma actuators produced with these nonstandard dielectric materials were analyzed in terms of electrical characteristics, generated flow velocity and mechanical efficiency, and the obtained results were compared with a standard actuator made of Kapton. An innovative calorimetric method was implemented in order to estimate the thermal power transferred by these devices to an adjacent flow. These results allowed to discuss the ability of these new dielectric materials not only for flow control applications but also for heat transfer applications.

This work reports on the production of poly(vinylidene fluoride) (PVDF) membranes by non-solvent induced phase separation (NIPS) using N,N-dimethylformamide (DMF) as solvent and water as non-solvent. The influence of the processing conditions in the morphology, surface characteristics, structure, thermal and mechanical properties were evaluated for polymer dissolution temperatures between 25 and 150 C and conditioning time between 0 and 10 min. Finger-like pore morphology was obtained for all membranes and increasing the polymer dissolution temperature led to an increase in the average pore size ( 0.9 and 2.1 m), porosity ( 50 to 90%) and water contact angle (up to 80 ), in turn decreasing the PVDF content ( 67 to 20%) with the degree of crystallinity remaining approximately constant ( 56%). The conditioning time did not significantly affect the polymer properties studied. Thus, the control of NIPS parameters proved to be suitable for tailoring PVDF membrane properties.

Dielectric barrier discharge (DBD) plasma actuators are simple electrohydrodynamic devices, which are able to provide effective aerodynamic control. One of the main components of these devices is the thin dielectric layer, which allows to separate and prevent the arc between the high-voltage electrodes. Different materials can be used as dielectric layer to reduce the power consumption or boost the flow controlling effect of the actuators. In this context, this report presents a comparative study of two commercial polyimides, Kapton and Cirlex, used as dielectric layer of surface DBD plasma actuators. The electrical, dielectric, mechanical, electromechanical, and thermal properties were obtained to evaluate overall performance. It was verified that Cirlex (8.3 W) consumes less power than Kapton (21.3 W) to generate higher induced flow velocity of ≈3.4 m/s for an input voltage of 11 kVpp and 24 kHz. During one AC cycle at 11 kVpp the charge transferred for Cirlex (70 nC) is lower than for Kapton (100 nC), as well as the dielectric breakdown voltage to ignite the plasma discharge, 1.5 and 2.2 kVpp, respectively. The Cirlex DBD presents a higher voltage operation limit (at least 14 kVpp) and a more regular plasma discharge, which results in a more homogenous thermal profile and temperature distribution during its operation. The Cirlex actuator delivered higher mechanical power (6.2 mW) and achieved higher electromechanical efficiency (0.004%). The polyimide Cirlex proved to be a suitable alternative for Kapton to fabricate DBD plasma actuators for flow control with improved performance.

Energy harvesting from the environment based on electroactive polymers has been increasing in recent years. Ferroelectric polymers are used as mechanical-to-electrical energy transducers in a wide range of applications, scavenging the surrounding energy to power low-power devices. These energy-harvesting systems operate by taking advantage of the piezoelectric, pyroelectric, and magnetoelectric properties of the polymers, harvesting wasted environmental energy and converting it mainly into electrical energy. There have been developed different nano- and micro-scale power harvesters with an increasing interest for powering mobile electronics and low-power devices, including applications in remote access areas. Novel electronic devices are developed based on low-power solutions, and therefore, polymer-based materials represent a suitable solution to power these devices. Among the different polymers, the most widely used in the device application is the poly(vinylidene fluoride) (PVDF) family, due to its higher output performance.

Structural health monitoring (SHM) is a nondestructive process of collecting and analyzing data from structures to evaluate their conditions and predict the remaining lifetime. Multifunctional sensors are increasingly used in smart structures to self-sense and monitor the damages through the measurements of electrical resistivity of composite materials. Polymer-based sensors possess exceptional properties for SHM applications, such as low cost and simple processing, durability, flexibility, and excellent piezoresistive sensitivity. Thermoplastics, thermoplastic elastomers, and elastomer matrices can be combined with conductive nanofillers to develop piezoresistive sensors. Polymer, reinforcement fillers, processing and design have critical influences in the overall properties of the composite sensors. Together with the properties of the functional composites, environmental concerns are being increasingly relevant for applications, involving advances in materials selection and manufacturing technologies. In this scenario, additive manufacturing is playing an increasing role in modern technological solutions. Stretchable multifunctional composites applications include piezoresistive, dielectric elastomers (mainly for actuators), thermoelectric or magnetorheological materials. In the following sections, piezoresistive materials and applications will be mainly addressed based on their increasing implementation into applications.