This paper aims to model the effect of grout composition on properties of two natural hydraulic lime (NHL) grouts based on the correlation between grout rheometer results and simple flow tests. First, the effects of water:binder ratio and superplasticizer dosage on its rheological properties and flowability were analyzed. Dosage of superplasticizer and water:binder ratio were varied from 0.6 to 1.2% (by mass of binder) and 0.45-0.55, respectively. A good correlation between classical flow tests and the rheological properties was obtained. Then, statistical models were formulated in order to estimating the grout parameters, such as plastic viscosity and yield stress just by performing simple flow tests. The models coefficients were calculated using multiple regression analysis. The statistical modeling results indicated that the properties of the grouts studied are linearly related to water:binder ratio, superplasticizer dosage, and specific surface area of natural hydraulic limes. Finally, the accuracy of the models was experimentally confirmed using random grout compositions. The predicted-to-measured ratio ranged from 0.97 to 1.08, indicating a good agreement between the confirmation results and the expected results from the statistical models.

This review provides an overview of the recent progress in the field of the rheology of grouts for historic masonry consolidation. During the last two decades, significant research has been devoted on the grouting technique for stone masonry consolidation but most results are scattered by scientific papers, congress communications, and thesis. This paper compiles and briefly demonstrates the effect of several intrinsic and extrinsic parameters, such as admixtures, additions, pressure, temperature, and measuring instrumentation, on the rheological performance of natural hydraulic lime-based grouts.

The injection of grouts is a consolidation technique suitable for overcoming the structural deterioration of old stone masonry walls. Grouting operations involve introducing a suspension (grout) into a masonry core with the aim of improving the load capacity of the wall, as well as reducing its brittle mechanisms. The yield stress of injection grouts will affect the injection pressure and their flow inside the masonry. However, the determination of some rheological properties such as yield stress in hydraulic grout is challenging, due to the combined effects of hydration reactions and interactions between the particles present in the suspension. In this study, the determination of the yield stress of natural hydraulic lime-based grouts with polypropylene fibers was carried out. The changes in yield stress with time, fibers content and hydration were evaluated by two measurement methods using a rotational rheometer. Additionally, the static and dynamic yield stress as well as the critical shear-strain rate were determined, which provided useful information on the grout design in order to achieve successful grouting operations.

Grout is a concentrated suspension that can be employed for the homogenisation and consolidation of systems presenting pores, voids and cracks, such as inner core of old stone masonries. A grout should be well conceived, taking into account the optimisation of its performance; this means that simple binder and water formulations prove to be inadequate. Hence, the effect of different admixtures and pozzolans, which are traditionally used in concrete, on the fresh and hardened properties of hydraulic lime grouts, were investigated. Hydraulic lime binder plays a role of great importance in the rehabilitation of historic structures, due to its compatibility with pre-existing materials, like mortars. However, hardly any information is presently known regarding the effect of these materials on the behaviour of hydraulic lime grouts. The improvement of their properties through the use of these products is still an open field. Hence, and as a first step, the prediction of grout properties in a laboratory setting were made. The results summarised in this paper are part of a large research project and precede the fine tuning of grout composition according to the characteristics of the masonry to which such a grout is to be injected.

Electrorheological fluids have been paying a lot of attention due to their potential use in active control of various devices in mechanics, biomedicine or robotics. An electrorheological fluid consisting of polarizable particles dispersed in a non-conducting liquid is considered to be one of the most interesting and important smart fluids. This work presents the effect of the dopant, camphorsulphonic acid or citric acid, on the electrorheological behaviour of suspensions of doped polyaniline nanostructures dispersed in silicone oil, revealing its key role. The influence of carbon nanoparticle concentration has also been studied for these dispersions. All the samples showed an electrorheological effect, which increased with electric field and nanostructure concentration and decreased with silicone oil viscosity. However, the magnitude of this effect was strongly influenced not only by carbon nanoparticle concentration but also by the dopant material. The electrorheological effect was much lower with a higher carbon nanoparticle concentration and doped with citric acid. The latter is probably due to the different acidities of the dopants that lead to a different conductivity of polyaniline nanostructures. Furthermore, the effect of the carbon nanoparticles could be related to its charge trapping mechanism, while the charge transfer through the polymeric backbone occurs by hopping. Polyaniline/camphorsulphonic acid composite nanostructures dispersed in silicone oil exhibited the highest electrorheological activity, higher than three decades increase in apparent viscosity for low shear rates and high electric fields, showing their potential application as electrorheological smart materials.

Gellan gum is a biocompatible and easily accessible polysaccharide with excellent properties to produce microparticles as drug delivery systems. However, the production methods often fail in reproducibility, compromising the translational potential of such systems. In this work, the production of gellan gum-based microparticles was optimized using the coaxial air flow method, and an inexpensive and reproducible production method. A design of experiments was used to identify the main parameters that affect microparticle production and optimization, focusing on diameter and dispersibility. Airflow was the most significant factor for both parameters. Pump flow affected the diameter, while the gellan gum/alginate ratio affected dispersibility. Microparticles were revealed to be sensitive to pH with swelling, degradation, and encapsulation efficiency affected by pH. Using methylene blue as a model drug, higher encapsulation, and swelling indexes were obtained at pH 7.4, while a more pronounced release occurred at pH 6.5. Within PBs solutions, the microparticles endured up to two months. The microparticle release profiles were studied using well-known models, showing a Fickian-type release, but with no alteration by pH. The developed microparticles showed promising results as drug-delivery vehicles sensitive to pH.